HDA not acquiring static IP
Posted: Mon May 25, 2020 11:42 am
Hi
I have the following error when creating an Amahi 11 server on my Proliant when I install use the normal method as well as from installing Fedora 27 followed by Amahi. This is not my first Amahi server, btw.
The server has two NICs eno1 and eno2 with only one connected. After install, the connected NIC gets an IP address via my router's IP while the second one is allowed a static IP that corresponds to my amahi setup.
This is what I get when i type in "IP addr show"
When I nano the config files in /etc/sysconfig/network-scripts/ for each interface, I get the following
eno1:
and the following for eno2:
To solve this, I flipped the configurations (i.e. in eno1, i changed teh BootProto to none and copied the lines from IPADDR down in eno2. When I booted it up, the server is now on the assigned static IP
Two questions
1. Is there any other setting changes that i need to worry about?
2. What is the docker interface that was installed by Fedora?
I have the following error when creating an Amahi 11 server on my Proliant when I install use the normal method as well as from installing Fedora 27 followed by Amahi. This is not my first Amahi server, btw.
The server has two NICs eno1 and eno2 with only one connected. After install, the connected NIC gets an IP address via my router's IP while the second one is allowed a static IP that corresponds to my amahi setup.
This is what I get when i type in "IP addr show"
Code: Select all
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 3c:a8:2a:9f:62:04 brd ff:ff:ff:ff:ff:ff
inet 192.168.0.169/24 brd 192.168.0.255 scope global dynamic eno1
valid_lft 80117sec preferred_lft 80117sec
inet6 fe80::f449:d437:e868:79ff/64 scope link
valid_lft forever preferred_lft forever
3: eno2: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
link/ether 3c:a8:2a:9f:62:05 brd ff:ff:ff:ff:ff:ff
inet 192.168.0.73/24 brd 192.168.0.255 scope global eno2
valid_lft forever preferred_lft forever
inet6 fe80::fd76:c2be:b8c1:b157/64 scope link tentative
valid_lft forever preferred_lft forever
4: docker0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default
link/ether 02:42:02:02:91:d3 brd ff:ff:ff:ff:ff:ff
inet 172.17.0.1/16 scope global docker0
valid_lft forever preferred_lft forever
eno1:
Code: Select all
TYPE=Ethernet
PROXY_METHOD=none
BROWSER_ONLY=no
BOOTPROTO=dhcp
DEFROUTE=yes
IPV4_FAILURE_FATAL=no
IPV6INIT=yes
IPV6_AUTOCONF=yes
IPV6_DEFROUTE=yes
IPV6_FAILURE_FATAL=no
IPV6_ADDR_GEN_MODE=stable-privacy
NAME=eno1
UUID=dd236dc2-47ac-3169-bdec-e961c129ed6a
ONBOOT=yes
AUTOCONNECT_PRIORITY=-999
DEVICE=eno1
PROXY_METHOD=none
BROWSER_ONLY=no
Code: Select all
TYPE=Ethernet
PROXY_METHOD=none
BROWSER_ONLY=no
BOOTPROTO=none
DEFROUTE=yes
IPV4_FAILURE_FATAL=no
IPV6INIT=yes
IPV6_AUTOCONF=yes
IPV6_DEFROUTE=yes
IPV6_FAILURE_FATAL=no
IPV6_ADDR_GEN_MODE=stable-privacy
NAME=eno2
UUID=7e0eda0e-0fac-37d5-bd4d-96772f656d6a
ONBOOT=yes
AUTOCONNECT_PRIORITY=-999
DEVICE=eno2
IPADDR=192.168.0.73
PREFIX=24
GATEWAY=192.168.0.1
DNS1=208.67.222.222
DNS2=208.67.220.220
Two questions
1. Is there any other setting changes that i need to worry about?
2. What is the docker interface that was installed by Fedora?